Kinshi High Tech Sieve IV
The High Tech Kinshi Sieve IV is a Pump Fed pre-filter to filter waste solids from the water via a pump. This technique incorporates a sieve-bend. A sieve-bend consists of hundreds of sharp stainless steel profile wires with very small slot openings where the water can go through but the solids stay on the sieve bend.
In practice it works as follows: The water enters the High Tech Kinshi Sieve IV via the Ultraskim or bottom drain and passes through the “auto-adjustable” dam and will go upwards and fall over the weir on to the Stainless Steel sieve-bend.
The water goes through the sieve bend and the waste solids will slowly go down to the waste area. At the waste outlet of the filter is a 2 inch male thread connection with end cap for attaching a 2 inch slide/Ball valve to easily wash away the waste with water. When the water in the tank underneath the sieve-bend is not pumped away fast enough the water will raise which makes the floating system (auto-adjustable dam) go up to reduce the incoming water flow.
The pump will be connected to the inlet of the sieve. You can use a pump like a Sequence 18000S Pump or Speck Badu Top or a submersible pump that can be used in the pond like the Oase Aquamax Eco 16000 or Oase Aquamax Start 8500 Pump.
An extra advantage of High Tech Kinshi Sieve IV pre-filter is that the water will be provided with extra oxygen, when it goes through the slots. Plus the mechanical waste is removed from the water itself.With Gravity fed sieves from a bottom drain or skimmer make sure the upper edge of High Tech Kinshi Sieve IV is 1 cm higher than the maximum water level, also its important to make sure the High Tech Kinshi Sieves are on an equal, level, ground.
Between the bottom drain and the High Tech Kinshi Sieves or a skimmer and the High Tech Kinshi Sieves we strongly advise you to use a slide valve or ball Valve to separate the High Tech Kinshi Sieves from the pond when necessary.
The inlets of the High Tech Kinshi Sieves are made of 110 mm Polypropylene pipe so you can use one of our rubber boots to join the two together. Since the High Tech Kinshi Sieves are made of Polypropylene you cannot make any glue connections. The High Tech Kinshi Sieve range have 1 inlet up to 3 inlets all 110 mm depending on which model and flow you require.
The High Tech Kinshi Sieve has a floating system to prevent the water in the area under the sieve from rising above the level of the sieve for low speed pumps and also to prevent the water from going too low to be primed for high speed pumps.
To remove the waste that is on the surface of the High Tech Kinshi Sieve is very easy by opening the waste outlet and to rinse the waste away with a normal hosepipe. Another method to have water run over the screen is pushing down the adjustable dam, which will flood the screen with water. When the adjustable dam is in a low position already because of the pump speed you can pull up the dam for a short while and push it back downwards again.
To remove the waste that has gone into the profile wires of the High Tech Kinshi Sieve (only when necessary) you will need a hosepipe with a powerful spray nozzle or a high-pressure machine. For this way of cleaning you have to place the sieve in an upright position or take the sieve out of the unit. After a certain period of time the sieve can get “fat” and this will make it more difficult for the water to go through. You can clean the sieve with i.e. alcohol. Note: when you use the sieve for the very first time the surface of the sieve can also be covered with a very thin film. Make sure you clean the sieve very thorough with alcohol before using it.
High Tech Kinshi Sieve IV Technical Specifications:
- Pump Fed Prefilter
- Pump capacity: 20 000 liters / hour
- Dimensions: 50 cm L x 47 cm W x 60 cm H
- Water supply: 1 x 110 mm
- Outlet: 1 x 63 mm
- Drain Plug: 1.5 inch (50 mm) with ball valve
- Stainless Steel 316 Screen 445 x 400 mm
- 300 micron Stainless Steel screen
- Standard lid on the screen
- Part No. 0088204
- Material: Polypropylene
- Colour: Sahara
The perfect solution for pump capacities up to ±20m³/h. (20000 lph) The most ideal pre-filter! Create a compact filter system by combining the High Tech Kinshi Sieve II with a beadfilter or other pump fed filters.